Daisy Wu
01020304
Pure sine wave output. THD ＜3%. The conventional conversion time is 6ms.
It can hold 300% overload within 20s, providing necessary current for starting electrical
appliances with high requirements. HP series is capable of starting and stopping the
generator, and realizing the function of monitoring the equipment operation status and
battery temperature etc.by mobile through additional communication modules.
-
THD<3% under standard load -
Multiple protection for safer use -
Switch time <8 m(to off grid mode)
-
Generator automatic start/stop function
Basic application
The system can use PV energy to power loads when grid is unavailable, minimizing the use of generator. Excessed PV energy can be stored in batteries and provide backup power during outages. Compensating with a generator to avoid power shortage issue.
Backup power scheme
It can be used as a stable and reliable backup power source, using photovoltaic energy to charge the batteries and seamlessly switching to standby mode in milliseconds to power critical equipment in the event of a grid failure. Coupled with a generator, it is possible to increase the amount of time spent off-grid at night.
-
Technical Parameter
+AP 8KW-20KW Pure Sine Wave Inverter & Charger Inverter
OutputModel 8.0KW 10.0KW 12.0KW 15.0KW 18.0KW 20.0KW Continuous Output Power 8.0KW 10.0KW 12.0KW 15.0KW 18.0KW 20.0KW Surge Rating (20Secs) 24.0KW 30.0KW 36.0KW 45.0KW 54.0KW 60.0KW Output Waveform Pure Sine vave/Same as input (Bypass Mode) Nominal Efficiency >88% (Peak) Line Mode Efficiency >95% Power Factor 0.9-1.0 Nominal Output Voltage 220-230-240Vac Output Voltage Regulation ±10%RMS Output Frequency 50Hz±0.3Hz / 60Hz±0.3Hz Short Circuit Protection Yes (1 sec after fault) Typical transfer Time 10ms (Max) THD < 3% (Rated battery level, rated full linear load) DC Input Nominal Input Voltage 24.0Vdc/48.0Vdc/96.0Vdc 48.0Vdc/96.0Vdc Minimum Start Voltage 10.0Vdc / 10.5Vdc for 12Vdc Mode *2 for 24Vdc/*4 for 48Vdc/*8 for 96Vdc Low Battery Alarm 10.5Vdc / 11.0Vdc for 12Vdc Mode Low Batteiy Trip 10.0Vdc / 10.5Vdc for 12Vdc Mode High Voltage Alarm 16.0Vdc for 12Vdc Mode Low Battery Voltage Recover 15.5Vdc for 12Vdc Mode ldle Consumption-Search Mode < 25W When Power Saver On Charger Output Voltage Depends on battery type Charger Breaker Rating 50A 80A 80A 100A Battery Initial Voltage for start 10-15.7Vdc for 12Vdc Mode *2 for 24Vdc / 4 for 48Vdc/ 8 for 96Vdc Over Charge Protection S.D 15.7Vdc for 12Vdc Mode Selector Switch Setting Description Fast Mode / VDC Float Mode / VDC 0 Charger Off 1 Gel USA 14 13.7 2 AGM 1 14.1 13.4 3 Lithium 13.8 13.6 4 Sealed Lead Acid 14.4 13.6 5 Gel EURO 14.4 13.8 6 Open Lead Acid 14.8 13.8 7 LifePO4 14 13.8 8 De-sulphation 15.5 (4 Hours then Off) 9 Classic LFP 13.6 13.5 For 12Vdc Mode Series(*2 for 24Vdc Mode/*4 for 48Vdc Mode/*8 for 96Vdc Mode) BTS Battery Temperature Sensor
(Optional)Yes ( Refer to the table) Variances in Charging Voltage & S.D Voltage Base on the Battery Temperature Bypass &
ProtectionInput Voltage Waveform Sine vave (Grid or Generator) Nominal Voltage 220-230-240Vac Max Input AC Voltage 300Vac For 230Vac HV Mode Nominal Input Frequency 50Hz or 60Hz Low Freq Trip 47±0.3Hz for 50Hz,57±0.3Hz for 60Hz High Freq Tip 55±0.3Hz for 50Hz,65±0.3Hz for 60Hz Over Load Protection
(SMPS load)Circuit Breaker Output Short Circuit Protection Circuit Breaker By pass Breaker Rating 50A 80A 80A 100A Transfer SWitch Rating 80AmpforUL&TUV 100Amp for UL Bypass Without Battery
ConnectedYes (Optional) Max Bypass Current 80 Amp 100Amp Mechanical
SpecificationsMounting Wall Mount Inverter Dimensions (L*W*H) 588*415*200mm 706*415*213mm Inverter Weight KG 60 66 70 85 95 100 Shipping Dimensions(L*W*H) 750*520*310mm 850*520*350mm Shipping Weight KG 62 68 72 87 97 102 Display Status LEDs / Status LEDs+LCD Standard Warranty 1 Year
